日常清潔 ：

　　Daily cleaning:

　　每次使用完去毛刺拋光機后，都要進行清潔工作，用抹布擦拭機器表面，確保沒有拋光液或其他雜質殘留在機器上。特別要注意拋光液不要濺射到機器上，因為這可能會損害機器表面。

　　After each use of the deburring and polishing machine, cleaning work should be carried out by wiping the surface of the machine with a cloth to ensure that no polishing solution or other impurities remain on the machine. Special attention should be paid not to splash the polishing solution onto the machine, as this may damage the surface of the machine.

　　拋光液管理 ：

　　Polishing solution management:

　　如果拋光桶里的水過熱（正常水溫范圍在50°C），應及時換水。拋光液濺到機器上后，應及時擦拭干凈，防止液體損害機器外表。

　　If the water in the polishing bucket overheats (the normal water temperature range is 50 ° C), it should be replaced in a timely manner. After the polishing solution splashes onto the machine, it should be wiped clean in a timely manner to prevent the liquid from damaging the appearance of the machine.

　　拋光針管理 ：

　　Polishing needle management:

　　放拋光桶時，拋光槽內若有拋光針，應及時清理。如果長時間不使用去毛刺拋光機，應將拋光的鋼針清洗干凈并放置在干燥的環境中，以增加其使用壽命。

　　When placing the polishing bucket, if there are polishing needles in the polishing tank, they should be cleaned in a timely manner. If the deburring and polishing machine is not used for a long time, the polished steel needle should be cleaned and placed in a dry environment to increase its service life.

　　控制面板保護 ：

　　Control panel protection:

　　去毛刺機閑置時，可以用膠袋套住控制面板，以防止灰塵進入。

　　When the deburring machine is idle, a plastic bag can be used to cover the control panel to prevent dust from entering.

　　潤滑與維護 ：

　　Lubrication and maintenance:

　　定期對機器的潤滑系統進行檢查，確保潤滑充分，并及時更換潤滑劑。同時，要定期檢查機器的各個部件，如砂帶、壓料棍等，根據需要進行調整和更換。

　　Regularly inspect the lubrication system of the machine to ensure adequate lubrication and promptly replace lubricants. At the same time, it is necessary to regularly inspect various components of the machine, such as sanding belts, pressing rods, etc., and adjust and replace them as needed.

　　機器校準 ：

　　Machine calibration:

　　定期校準去毛刺機的各個部件，以確保設備的正常運行和加工精度。

　　Regularly calibrate the various components of the deburring machine to ensure the normal operation and machining accuracy of the equipment.

　　安全操作 ：

　　Safe operation:

　　在操作去毛刺拋光機時，一定要遵守設備的安全規定，穿戴防護裝備，防止發生意外傷害。

　　When operating the deburring and polishing machine, it is necessary to comply with the safety regulations of the equipment, wear protective equipment, and prevent accidental injuries.

　　備份與檢查 ：

　　Backup and Inspection:

　　定期備份設備的重要參數和數據，以防萬一。同時，定期對設備進行檢查和維護，及時發現并解決故障，避免因設備問題導致的生產停滯。

　　Regularly backup important parameters and data of the equipment, just in case. At the same time, regular inspections and maintenance of equipment are carried out to promptly detect and resolve malfunctions, avoiding production delays caused by equipment problems.

　　儲存 ：

　　Storage:

　　如果短期不再使用機器，將機器盡量放入室內，存放于0℃以上的空間，防止低溫出現結冰情況。如果長期不再使用機器，需要把機器放在一個環境相對于干燥的空間中，可對機器內部部件涂抹防凍液，或是用防護套件進行保護，以防腐蝕。

　　If the machine is no longer in use in the short term, try to store it indoors in a space above 0 ℃ to prevent freezing at low temperatures. If the machine is not used for a long time, it needs to be placed in a relatively dry environment. Antifreeze can be applied to the internal components of the machine, or protective kits can be used to prevent corrosion.

　　本文的精彩內容由高壓去毛刺清洗機提供知識提供，本網站還有很多的精彩內容，更多的內容您可以點擊進入：http://www.qdnggxh.com我們有專門的客服為您解答問題

　　The exciting content of this article is provided by the knowledge of high-pressure deburring cleaning machine. There are also many exciting contents on this website. For more content, you can click to enter: http://www.qdnggxh.com We have dedicated customer service to answer your questions